Edelbrock E-Series Cylinder Head Bolt Kit #85572 is a high-quality set of replacement bolts for use with Ford FE 390-428 heads. This kit contains all the necessary parts top replace the factory head bolts. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock E stamped into the head.

Edelbrock Edelbrock E-Series Cylinder Head Bolt Kit #85572 for Ford 390-428 FE engines 85572

Specifications:

RGL	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
9	Hex
10	8740 Chromoly
546	Coarse
557	0.5
3072	Yes
Finish	Black Oxide
Grade Type	Performance
Quantity	Kit
Length	(10) 4.450 in, (10) 2.875
Description_ABR	HeadBoltKit
Description_INV	Edelbrock Cylinder Head Bolt Kit #85572
Description_LAB	Edelbrock E-Series Cylinder Head Bolt Kit #85572 for Ford 390-428 FE engines
Description_DES	Edelbrock E-Series Cylinder Head Bolt Kit #85572 for Ford 390-428 FE engines
Description_SHP	None
Description_ASM	Ford:FE:390 (6.4L)-428 (7.0L)
Description_EXT	Edelbrock #85572 is a Head Bolt Kit for 1958-76 Ford FE 390-428 heads and FE engines equipped with Edelbrock 60059, 60089, 60065, 60069, 60075, & 60079 Performer RPM Cylinder Heads. Complete set of Head Bolts & Washers for a pair of heads.
Description_MKT	Edelbrock E-Series Cylinder Head Bolt Kit #85572 is a high-quality set of replacement bolts for use with Ford FE 390-428 heads. This kit contains all the necessary parts top replace the factory head bolts. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock E stamped into the head.
Description_FAB	For Ford FE 390-428 heads
Description_FAB	Yield tensile strength of 190,000 PSI
Description_FAB	Heat treating with rolled threads for superior form and strength
Description_FAB	black-oxide finish with sealer
Description_FAB	Edelbrock E logo stamped on bolt head
Description_TRA	The Edelbrock #8557 is made specifically for
Description_TRA	Installation is the same as for original equipment cylinder heads. Consult service manual for specific procedures, if necessary.
Description_TRA	Be sure that the surface of the block and the surface of the head are thoroughly cleaned to remove any oily film before installation.
Description_TRA	Use alcohol or lacquer thinner on a lint-free rag to clean. Apply oil or suitable thread lubricant to head bolt threads and the underside of bolt heads and washers to prevent galling and improper torque readings.
Description_TRA	Use thread sealant on any bolts that go into coolant passages. Torque top row of bolts to 110 ft./lbs. and bottom row of bolts to 100 ft./lbs. in three or four steps, following the factory tightening sequence. A re-torque is recommended after the initial star-up and cool-down (allow 2-3 hours for adequate cooling)
Description_DEF	Engine Cylinder Head Bolt Set