Edelbrock E-Series Cylinder Head Bolt Kit #85332 is designed for use on Jeep 4.0L inline six-cylinder engines using -inch head bolts. This high-quality E-Series bolt kit will pair perfectly with Edelbrock's Jeep Cylinder Head #50159 and #50169 and will also fit the 4.2L inline six-cylinder engine if using Edelbrock heads. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock E stamped into the head.

Edelbrock Edelbrock E-Series Cylinder Head Bolt Kit #85332 for Jeep 4.0L Inline Six Engine 85332

Specifications:

RGL	WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
9	Hex
10	8740 Chromoly
546	Coarse
557	0.5
3072	Yes
Finish	Black Oxide
Grade Type	Performance
Quantity	Kit
Length	(7) 3.75 in, (7) 4.50
Description_ABR	HeadBoltKit
Description_INV	Edelbrock Cylinder Head Bolt Kit #85332
Description_LAB	Edelbrock E-Series Cylinder Head Bolt Kit #85332 for Jeep 4.0L Inline Six Engine
Description_DES	Edelbrock E-Series Cylinder Head Bolt Kit #85332 for Jeep 4.0L Inline Six Engine
Description_SHP	None
Description_ASM	Jeep:Inline-Six:242 (4.0L)
Description_EXT	Edelbrock #85332 Head Bolt Kit is for Jeep 4.0L inline six engines using 1/2" head bolts with Edelbrock #50159 and #50169 Cylinder Heads. This Head Bolt Kit will also fit AMC/Jeep 4.2L Inline Six if using our cylinder heads.
Description_MKT	Edelbrock E-Series Cylinder Head Bolt Kit #85332 is designed for use on Jeep 4.0L inline six-cylinder engines using -inch head bolts. This high-quality E-Series bolt kit will pair perfectly with Edelbrock's Jeep Cylinder Head #50159 and #50169 and will also fit the 4.2L inline six-cylinder engine if using Edelbrock heads. E-Series bolts have a yield tensile strength of 190,000 PSI for strong and reliable loading with generous filleting throughout to eliminate stress risers. Bolt threads are rolled after heat-treating for superior form and strength, while a small hex head provides extra space for socket clearance in tight situations. E-Series Cylinder Head Bolts have a durable black oxide finish with sealer and come with the distinctive Edelbrock E stamped into the head.
Description_FAB	For Jeep 4.0L inline six with -inch bolt diameter
Description_FAB	Yield tensile strength of 190,000 PSI for strength
Description_FAB	Heat treating with rolled threads for superior form & strength
Description_FAB	Black-oxide finish with sealer
Description_FAB	Edelbrock E logo stamped on bolt head.
Description_TRA	The Edelbrock #85332 is made specifically for Jeep 4.0L
Description_TRA	Installation is the same as for original equipment cylinder heads.
Description_TRA	Consult service manual for specific procedures, if necessary.
Description_TRA	Be sure that the surface of the block and the surface of the head are thoroughly cleaned to remove any oily film before installation.
Description_TRA	Use alcohol or lacquer thinner on a lint-free rag to clean. Apply oil or suitable thread lubricant to head bolt threads and the underside of bolt heads and washers.
Description_TRA	Torque cylinder head bolts in three steps following the factory tightening sequence
Description_DEF	Engine Cylinder Head Bolt Set